Apopka Electrical Company is a full-service residential and commercial electrician serving Apopka and Orange County. Whether you have a tripped breaker that won't reset, a panel that's overdue for an upgrade, or a new build that needs wiring from the ground up, we handle the job from the first call to the final test. Short-notice calls are welcome, and scheduling is confirmed when you call.
We answer the phone. We show up ready to work. We test before we leave.
Call (689) 362-1899 for a quote.
Good electrical work isn't complicated, it's just done right, and that starts with finding the actual problem before anything gets touched. Flickering lights, dead outlets, a breaker that trips every time you run the microwave, a burning smell near a switch, buzzing from the panel, sparks when you plug something in - these are all symptoms, and the cause is not always obvious from the surface.
When we come out for a diagnostic visit, we trace the fault to its source. That means checking the circuit, testing the outlet or switch, inspecting the wiring at the device and at the panel, and giving you straight answers about your panel and wiring before any repair work is quoted. We cover GFCI and AFCI protection as part of that process where it applies, and we check grounding and bonding when the symptom points that direction.
No power in one room, outlets that stopped working after a storm, a breaker that hums or feels warm - these are not problems to leave until later. One call and we are on it.
From older homes to new commercial builds, the panel is where every circuit in the building starts. When a panel is undersized, outdated, or simply worn out, it shows up in tripped breakers, flickering lights, and circuits that can't carry the loads the building actually needs.
We handle full panel replacements, upgrades from 100-amp to 200-amp service, service entrance upgrades, subpanel installation, and load calculations for properties that are adding new equipment. Arc-fault and ground-fault breakers are part of the work where code requires them, and we make sure the finished panel is electrical work done to the standard the next inspection expects.
In Apopka and across Orange County, the most common drivers of a panel upgrade are EV charger installations, new pool equipment, and major appliance additions. If you are adding a Level 2 charger, a pool pump, or a second HVAC disconnect to a panel that was sized for a different era, the math on the load has to be done before the new circuit goes in. We do that calculation as part of every panel quote.
Leave the breakers to us.
Homes and businesses need different wiring answers, but the standard for the work is the same. A dead outlet in a kitchen, a switch that controls nothing, a dimmer that flickers or buzzes, a garage outlet that trips every time it rains - each of these has a specific cause and a specific fix.
We install and replace GFCI outlets in kitchens, bathrooms, garages, and outdoor locations where code requires them. AFCI protection for bedrooms and living areas is part of what we do when a circuit is being replaced or extended. For older outlets that have simply failed, we diagnose whether the device itself is the problem or whether the wiring behind it needs attention.
Apopka has a mix of housing stock, including older homes where the original wiring is reaching the end of its useful life. A whole-home rewire is not a small job, but it is a straightforward one when it is planned and executed properly. We protect your floors and finishes while we work, and we keep disruption to the home to a minimum throughout the process.
We'll handle the wiring so you don't have to.
From a single GFCI outlet to a whole-home rewire, the first step is the same, and lighting work is no different. We start by understanding what the space needs before anything goes into the ceiling or wall.
Recessed and LED lighting, under-cabinet lighting, ceiling fan installation and replacement, outdoor and landscape lighting, security lighting, motion sensor fixtures - these are all regular work for us. In Apopka's climate, outdoor lighting and ceiling fans are not seasonal items. They are in use year-round, which means installation quality and weatherproofing matter more here than in places where a fixture sits dormant for months at a time.
Security lighting for residential and commercial properties is a frequent request. A motion sensor light at a side gate or a well-placed fixture covering a parking area does a specific job, and we wire it to do that job reliably. We're ready to get your circuits working again.
Major appliances need their own circuits. An electric range, a refrigerator, a washer and dryer, a dishwasher - running any of these on a shared circuit is a load problem waiting to become a breaker problem. We install dedicated circuits sized for the appliance, with the right wire gauge and breaker rating for the load.
EV charger installation is growing steadily across Orange County. A Level 2 home charger needs a dedicated 240-volt circuit, and the panel has to have the capacity to carry it. Every EV charger quote we give includes a panel capacity check, because adding a 50-amp circuit to a panel that is already near its limit is not a straight swap.
A price agreed before every visit. Clear scheduling every visit. Code-compliant every visit.
The sooner you call, the sooner the power is back on, and in Central Florida that urgency is real. Hurricane season runs from June through November. Lightning strikes are a regular occurrence, not a rare one. Backyard pools are common across Apopka and the surrounding area. These are not edge cases - they are the conditions that shape what electrical work matters most here.
We handle the jobs that come directly out of this climate. Clear communication from the first call to the final test is how we work through every one of them. You know who to call if you ever need us again.
When the power goes out during a storm, a properly wired standby generator keeps the lights on, the refrigerator running, and the essential circuits live. We handle the full electrical side of a generator installation: the transfer switch, the panel integration, the wiring from the generator to the disconnect, and the load assignment for the circuits you need covered. Storm season in Central Florida is long, and power outages in Orange County during active weather are not uncommon. Getting the electrical hookup done correctly before the season starts is the right time to do it.
Florida leads the country in lightning strikes per square mile, and a single event can damage a panel, destroy appliances, and corrupt electronics throughout a home or business. A whole-home surge protector installed at the panel level intercepts that voltage before it reaches the circuits. It works alongside proper grounding and bonding to give the system a path to dissipate excess energy rather than push it through your devices. This is not optional coverage in Apopka - it is practical protection for the environment the building actually sits in.
Pool ownership is common in Apopka, and the electrical work that goes with it is safety-critical. A pool pump needs a dedicated circuit sized for the motor. Spa equipment has its own load requirements. The entire pool surround requires bonding to bring all the metal components to the same electrical potential, which is a code requirement and a direct safety measure. Outdoor GFCI protection at the equipment and at nearby outlets is part of every pool wiring job we do. If the panel does not have the capacity for the new circuits, that gets addressed before the equipment goes in.
A home electrical inspection gives you a clear picture of what the wiring, panel, outlets, and circuits actually look like - not what you assume they look like. For buyers doing due diligence before closing, for landlords managing rental properties, and for property managers keeping a portfolio up to standard, an inspection is a practical tool rather than a formality.
We carry out pre-purchase inspections, rental property inspections, and standalone safety inspections for homeowners who want to know where their system stands. The inspection covers the panel, visible wiring, outlets, GFCI and AFCI protection, grounding, and any obvious hazards. Where an inspection is part of a larger panel upgrade or rewire quote, we fold it into the scoping process.
On the commercial side, we work with offices, retail spaces, and light commercial properties throughout Apopka and Orange County. Electrical repairs, circuit additions, panel work, lighting upgrades, and outlet installations for commercial spaces all fall within what we do. If you manage multiple properties or a commercial space with recurring electrical needs, call us and we will scope the work on the phone.
When you call, the conversation covers what the job involves, what we need to do it, and what it will cost. The price is confirmed before anything is scheduled, and you get a straight answer about what that price covers.
We do not quote a number without understanding the job, and we do not schedule a visit without a price agreed. If the scope changes once we are on site because something unexpected comes up in the wall or the panel, we explain it before the work continues.
We are open every day from 6:30 AM to 9:30 PM. Short-notice calls are welcome, and we take urgent work when the schedule has room.
We work throughout Apopka and take calls from across the wider region. Nearby communities we serve regularly include:
If you are just outside Apopka, call and ask. We cover more of Orange County and the surrounding area than this list suggests.
A whole-home surge protector is mounted at the main panel and connected to the service entrance. It intercepts large voltage spikes, including those caused by lightning strikes, before they reach the circuits feeding appliances and electronics throughout the building. It works alongside proper grounding and bonding, and those are checked as part of the installation. A power strip with surge protection handles only the device plugged into it and is not a substitute for panel-level protection.
A transfer switch isolates your home's wiring from the utility line when the generator is running. Without it, the generator could back-feed power onto the utility line, which creates a hazard for anyone working to restore power outside. We install the transfer switch, wire it to the panel, and test the full circuit before the job is complete. Both manual and automatic transfer switch installations are part of what we handle.
A pool pump needs a dedicated circuit sized for the motor load. The entire pool surround requires bonding, which brings all the metal components to the same electrical potential and is a code requirement, not a preference. GFCI protection is required at the equipment and at nearby outdoor outlets. If the panel does not have capacity for the new circuits, that is addressed before the equipment goes in.
Breakers that trip under normal loads, breakers that feel warm to the touch, a panel that hums or buzzes, double-tapped breakers where two wires share a single terminal, and visible corrosion or scorch marks inside the panel are all signs that the panel needs attention. A fuse box in a home that has added modern appliances is a related concern. Any of these conditions is a reason to have the panel looked at before adding more load.
A panel inspection covers the breaker condition, wiring connections at each terminal, whether any breakers are double-tapped, the rating of the service entrance relative to the home's load, and whether arc-fault and ground-fault breakers are in place where code requires them. We also check the grounding and bonding at the panel and note any visible corrosion or heat damage. The findings are explained before any repair or upgrade work is quoted.
GFCI protection is required in areas where water is present or nearby: kitchens, bathrooms, garages, outdoor locations, and around pools and spas. It cuts power when it detects a ground fault, which protects against shock. AFCI protection is required in bedrooms and living areas and is designed to detect arc faults in wiring, which are a leading cause of electrical fires. Both are code requirements in specific locations, and we install them wherever the work calls for them.
Flickering lights can point to a loose connection at the fixture, a failing switch, a circuit that is being overloaded by a large appliance starting up, or a wiring fault further upstream. Dimming that happens throughout the house when a specific appliance runs often points to a panel or service entrance issue rather than a problem at the fixture. Either symptom is worth a diagnostic visit if it is happening regularly, because the cause is not always obvious from the surface.
An outlet that sparks when you plug something in, a switch that buzzes or feels warm, a receptacle where plugs fit loosely and fall out, or an outlet that stops working intermittently are all signs of a connection problem. These are not issues to leave unattended, because a loose connection creates heat at the termination point over time. A diagnostic visit identifies whether the device itself has failed or whether the wiring behind it needs attention.
Outdoor wiring requires conduit and wire types rated for exposure to moisture, UV, and temperature variation. In Apopka's climate, that exposure is year-round rather than seasonal, which makes material selection and installation quality more consequential than in cooler or drier regions. GFCI protection is required at outdoor outlets, and all exterior fixtures and junction boxes need to be rated for outdoor use. We confirm the right materials and protection devices for the location before the work begins.
A repair is the right call when the fault is isolated: a single failed outlet, a broken switch, a tripped breaker caused by a specific appliance. A rewire becomes the conversation when the wiring itself is the problem across multiple circuits, when the existing wiring type is no longer adequate for the load, or when an inspection reveals that the system does not meet current standards in a way that cannot be addressed circuit by circuit. We scope which situation applies before quoting anything.
Permit requirements depend on the scope of the work and the jurisdiction. Panel replacements, new circuits, and whole-home rewires typically require a permit and a subsequent inspection in Orange County. We confirm what applies to your specific job when we scope it, and the work is carried out to the standard the inspection expects. Ask about permit requirements when you call and we will give you a straight answer for your address.
Clear access to the electrical panel is the most important thing. If the panel is in a closet, garage, or utility room, move anything stored in front of it. For outlet or switch work, move furniture away from the walls where we will be working. For attic or crawl space access, confirm that the entry point is reachable. We will let you know on the call if the job requires anything specific beyond that.
Apopka Electrical Company is available every day from 6:30 AM to 9:30 PM. Whether the job is a repair diagnosis, a panel upgrade, or a generator hookup planned before storm season, the process starts with a call.
We answer the phone. We show up ready to work. We test before we leave.
Call (689) 362-1899 for a quote.
From a tripped breaker to a full panel upgrade, we handle the electrical work that keeps homes and businesses in Apopka running safely. The table below covers what each service includes, who it fits best, and what is worth knowing before you call. If a job is not listed or you are not sure which service applies, call us and we will scope it on the phone.
| Type of Work | Scope of Work | Best For | Good to Know |
|---|---|---|---|
| Electrical Repairs & Troubleshooting |
| Any home or business with an unexplained electrical symptom | The cause of a symptom is not always at the device itself. We trace the fault to its source before quoting any repair work. |
| Lighting Installation |
| Homeowners upgrading interior lighting or adding exterior security coverage | In Apopka's climate, outdoor fixtures are in use year-round. Material selection and weatherproofing matter more here than in cooler regions. |
| Wiring & Circuit Installation |
| Older homes with wiring that has reached the end of its useful life, or any property adding new circuits | Apopka has a range of housing ages. Where older wiring is the underlying problem, a rewire is a straightforward job when it is planned correctly. |
| Breaker & Fuse Repair |
| Homes where breakers trip repeatedly or a fuse box is still in service | A breaker that trips under normal load is telling you something. We check the breaker, the circuit, and the load before replacing anything. |
| Ceiling Fan Installation |
| Any room adding or replacing a ceiling fan, especially where no existing wiring is present | If the ceiling box was not rated for a fan, we replace it before the fan goes up. That is a safety requirement, not an upsell. |
| Outlet & Switch Installation |
| Kitchens, bathrooms, garages, and any room with failing or missing outlets | GFCI protection is required by code in kitchens, bathrooms, garages, and outdoor locations. We install to current code on every job. |
| Electrical Safety Inspections |
| Buyers before closing, landlords managing rentals, and homeowners who want to know where their system stands | An inspection gives you a clear picture of what the system actually looks like. Findings are explained before any repair or upgrade work is quoted. |
| Surge & Lightning Protection |
| Any Central Florida home or business where lightning exposure is a real and recurring risk | Florida leads the country in lightning strikes per square mile. A panel-level protector intercepts voltage before it reaches your circuits and appliances. |
| Pool & Spa Wiring |
| Apopka homeowners installing or upgrading pool and spa equipment | Bonding all metal components around the pool is a code requirement and a direct safety measure, not optional. We include it in every pool wiring job. |
| Electrical Panel & Service Upgrades |
| Homes adding EV chargers, pool equipment, or major appliances to an undersized panel | Panel upgrades in Orange County typically require a permit and a subsequent inspection. We confirm what applies to your address when we scope the job. |
| Dedicated Appliance Circuits |
| Any home adding a major appliance or workshop equipment to an existing circuit | Running a large appliance on a shared circuit is a load problem waiting to become a breaker problem. A dedicated circuit is sized for the actual draw. |
| Whole-Home Generator Installation |
| Apopka homeowners preparing for hurricane season and extended power outages | Getting the hookup done before storm season starts is the right time. We handle the full electrical side, not the generator unit itself. |
How do I know if my home needs a panel upgrade or a service upgrade?
The most common signs are breakers that trip under normal household loads, circuits that cannot handle the appliances you are running, and a panel that was sized for a different era of electrical use. If you are adding an EV charger, pool equipment, or a large appliance, we run a load calculation before the new circuit goes in. That tells us whether the panel has the capacity or whether an upgrade has to happen first.
What causes a breaker to trip repeatedly?
A breaker trips when the circuit is drawing more current than the breaker is rated for, when there is a ground fault or arc fault on the circuit, or when the breaker itself is failing. The fix depends on the cause. An overloaded circuit may need a dedicated circuit or a panel upgrade. A faulty device on the circuit may be pulling too much current. A failing breaker needs to be replaced. We trace the cause before recommending anything.
Is older wiring in a home a safety concern?
It depends on the wiring type and condition. Aluminum branch circuit wiring from the 1960s and 1970s requires specific attention at connections, because aluminum expands and contracts differently than copper and can loosen over time. Knob-and-tube wiring, found in some older Apopka homes, was not designed for modern loads and lacks a ground conductor. Neither is an automatic emergency, but both warrant an inspection to understand what the system actually looks like before any work is added.
Faults Traced Before Anything Is Replaced
We find the source of the problem before quoting a repair. A symptom at the outlet or fixture is often caused by something upstream, and replacing the wrong part wastes time and money.
What does an EV charger installation involve?
A Level 2 home charger requires a dedicated 240-volt circuit with the right wire gauge and a 50-amp breaker in most cases. Before we run the circuit, we check the panel capacity. Adding a 50-amp circuit to a panel that is already near its limit is not a straight swap, and we do that calculation as part of every EV charger quote. If the panel needs to be upgraded first, we scope both jobs together.
How is a backup generator hookup different from just plugging one in?
A portable generator plugged directly into the home without a transfer switch can back-feed power onto the utility line, which creates a hazard for anyone working to restore power outside. A proper hookup requires a transfer switch that isolates your home's wiring from the utility when the generator is running. We install the transfer switch, wire it to the panel, assign the priority circuits, and test the full system before the job is complete.
When should I call an electrician instead of handling something myself?
Replacing a light bulb or resetting a tripped breaker is a reasonable first step. Beyond that, electrical work inside walls, at the panel, or at the service entrance carries real risk and typically requires a permit and inspection in Orange County. A warm outlet, a buzzing switch, sparks when plugging in a device, or a breaker that trips repeatedly are all reasons to call rather than investigate further on your own. Getting the diagnosis wrong can make the underlying problem harder to find later.
Code-Compliant Work on Every Job
Every job we complete is done to the standard the next inspection expects. Where a permit is required, we confirm that before the work starts and account for it in the schedule.
How long does a panel upgrade typically take?
Most panel replacements are completed in a single day. The utility has to disconnect and reconnect service, which adds coordination time depending on the utility's schedule in your area. We confirm the expected timeline when we scope the job. If a permit is required, we factor in the inspection into the overall schedule so there are no gaps in your coverage.
What is the risk of a warm or buzzing outlet?
A warm outlet or a switch that buzzes or feels hot at the cover plate is a sign of a loose connection or a device that is failing. A loose connection creates heat at the termination point, and heat at a connection point is how electrical fires start inside walls. This is not a symptom to monitor and revisit later. A diagnostic visit identifies whether the device itself has failed or whether the wiring behind it is the problem.
Scope Agreed Before the Panel Is Opened
The price and the scope are confirmed before anything is scheduled. If something unexpected comes up once we are on site, we explain it before the work continues.
Do I need to add circuits if I am setting up a workshop or garage space?
Workshop equipment, air compressors, table saws, and welders draw significantly more current than standard household outlets can reliably supply. Running that load on a shared circuit trips breakers and stresses the wiring. A dedicated circuit sized for the equipment is the right answer. We size the wire gauge and the breaker to the actual draw of the equipment you are running, not a generic estimate.
What does surge protection at the panel level actually do that a power strip does not?
A power strip with built-in surge protection covers only the devices plugged directly into it. A panel-level surge protector intercepts large voltage spikes at the service entrance before they reach any circuit in the building. In Central Florida, where lightning is a regular occurrence rather than a rare event, that difference matters. A single strike that gets past a power strip can damage appliances, electronics, and the panel itself throughout the home.
How do I know if my home is ready for added electrical load?
The panel rating, the condition of the existing circuits, and the current load on the service entrance all factor into whether a home can carry additional load. We run a load calculation when a new circuit or a major appliance is being added. If the panel is already near capacity, adding more load without addressing that first creates ongoing breaker problems and potential wiring stress. The calculation is part of every quote where new load is involved.
Call (689) 362-1899 and we will talk through what the job involves, what it will cost, and when we can get it done.
(689) 362-1899